• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Change a Subaru Spare Key

When you lose your Subaru car key, contact a locksmith. Locksmiths are usually able to cut you a key for less than the dealer.

Subaru car keys are generally either smart "push-to-start" fob remote keys or simple metal keys. The Fob key needs to have its chip programmed.

Keyless Entry System

The key fob can be used to lock and unlock your Subaru remotely. It can also open the trunk of your vehicle or the lift gate. These remotes function with the keypad in your car to communicate with the computer system inside the vehicle.

Certain models of subaru keys lost; click through the next internet site, have a feature that is not widely known called PIN Code Access. This allows you to use a personalised number sequence to start and open your car. Refer to the owner's manual for learn how to use this feature if you have a Subaru Forester, Outback Crosstrek, WRX STI or Impreza.

It's possible that the battery in the key fob has died. You can check the battery life of your key fob with an electronic tester that you can carry around or a multimeter you can find in your garage.

Next, you'll want to remove the key fob from its case and inspect its circuit board for the transmitter. This will have one or two sets of eight-digit numbers, so write down the first set so you can recall it later. Once you've finished then put the key fob back together and you'll be able to begin programming it at home. The procedure varies based on the year and model of your vehicle. However, it is generally easy enough to do yourself.

Key Fobs

Subaru's latest models come with key fobs that don't just unlock the doors however, they also activate your lights, lock your gas cap, and start your car. This feature is especially helpful if you've encountered yourself at the gas station and your car won't even start because the battery inside the key fob has failed.

It's likely that your Subaru's key fob, whether it is old or new it is able to be replaced. Be aware that some of the most modern models, with their high level technology, might require an appointment with a dealer. With some effort and time, you can build your own key fob replacement.

Begin by opening the case and looking at the circuit board of the transmitter. (Instructions on opening the case are usually found in the owner's guide). There should be one or two serial numbers of 8 numbers each. Note down the first number in the series and save it to refer to later.

Then, sit in the driver's seat, and close all of the doors. Turn the key to start your vehicle before turning off after ten revolutions. Press the lock button of your key fob, and then open the door. This will test that your doors are working correctly. After that close the door, and take the key out of the ignition. The chime should be heard from your vehicle again to indicate that the key fob is programmed.

Ignition System

If your Subaru keys aren't working as they should, it could be because the key battery is dead. If you know how, you can change the battery on your key fob yourself. The replacement subaru keys of the battery is affordable and easy to find. If your key fob doesn't respond to your commands, it might be another issue. It's best to visit a dealership to purchase a spare key. They can ensure that the key is genuine Subaru key, that is in warranty, and is programmed to your vehicle. This is much simpler and more secure than purchasing an aftermarket key from a company online.

You can also request that the dealer cut a brand new key if you supply them with your VIN number as well as evidence of ownership. They'll use this information to code the new key in order to be accepted by your immobilizer. This is more complex than cutting a key, and the dealership will usually charge a higher price for this service.

Once the new key has been programmed, you can replace it into your working key. It takes only five seconds to insert the new key, so make sure to keep your working key at fingertips. You can take the key off after the security light been off and you've tested it.

Battery Replacement

One of the primary features that make Subaru fobs useful is their ability to switch on your car's power windows and sunroof with a single touch of a button. However, the battery that is in your Subaru fob isn't meant to last forever. It will eventually require replaced. This quick guide from Capitol Subaru will help you to replace the battery on your own.

To begin you'll need to find the small crevice in the seam that divides the back and front of your key fob. You can cut this gap using the flat-head screwdriver, which will reveal the small compartment that houses the battery. Install the new battery and make sure it's facing in the correct direction. Remove the old one. After you've put everything together, you can use the new key fob to lock in, unlocking, and even starting your vehicle.

You should always have a spare set of keys, particularly if yours is broken or lost. You can purchase a brand new key at your local dealership or get it cut by locksmiths. Either way, it's important to get your key fob functioning properly in the shortest time possible to allow you to drive safely!