• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your Fiat 500 Key Fob Won't Work

A fiat ducato replacement key 500 key fob is a handy way to unlock the doors and start the car. There are many reasons why the key fob might stop working. These include a dead coin battery or water damage, receiver module issues, or interference.

This listing is for an NEW replacement fiat punto car key replacement remote key replacement (visit the website) Flip Key Remote - look-alike Ilco brand that must be programmed professionally by a local automotive locksmith (click here for Locksmith Search). This remote includes trunk, lock and unlock buttons.

Dead Coin Battery

The most frequent reason why your 500 key fob will not function is due to an inactive battery. Key fobs of today have only a limited range of operation and must be within a few inches of the vehicle to function. If you're not close to your vehicle and you press the key fob button the car will not respond, and will display an "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the battery of your coin cell (Part number CR2032) with a brand new one from a reliable brand such as Panasonic, Duracell, or Energizer. You can find them in your local hardware store, or on the internet.

After you've replaced the coin cell battery, you can test it by standing in front of your fiat punto car key 500 and pressing the buttons. The car should flash its parking lights, and the key fob will operate the lock and unlock switches.

If the key fob doesn't function after replacing the battery, it could have water damage that prevents it from communicating with the receiver module inside your car. Water damage can happen in a variety of ways, such as a simple splash or submerging the key fob in saltwater at the beach. If you suspect your fob has been exposed to water, try placing it in a dry rice bag to draw the moisture out. If this fails, you'll have to get your fob reset by an auto locksmith or a dealer.

Water Damage

Damage to the water supply can occur if you immerse the fob into the ocean, or wash it in a washing machine. Saltwater can cause the circuit board to short and eventually cease to function. Getting the fob wet is not an ideal choice but if you accidentally drop it in a glass of water or fail to take it out of your pocket before you run the washer and you don't have a chance, don't give in.

First take the battery off the fob. Before replacing the battery clean the electronic chip using isopropyl, or a similar product. Test the fob next to verify if it's working. If the fob doesn't work, it may have to be changed. This is usually done by an auto locksmith or dealer.

If the key is older and hasn't been programmed to your car, it will likely need to be replaced completely. A professional automotive locksmith will be able to complete this process. The locksmith will require the key cut to match your vehicle's ignition. They will also need to reprogram the fob for the car's system. This is a quick and cost-effective process that is usually completed within the same day.

Receiver Module Issues

One of the most common reasons why your 500 key fob may stop functioning is because it's out of range. The remote has a range of 30 feet. So in the event that you are far from your vehicle, it won't respond to your commands. It can be solved by moving it closer to your vehicle until it begins responding.

If your fob doesn't work after replacing the coin battery, also called a "button", "watch" or "button" or "button", it could be due to a problem with the circuit board inside. In the majority of cases, reprogramming your fob will fix the issue. You can find directions on how to do this on the majority of vehicles by searching YouTube or looking through the owner's manual.

You may need to replace the metal clips that keep the coin battery in place. If they lose tension it can prevent your coin battery from sitting properly, causing your remote to malfunction.

In rare cases the fob might become disconnected from your vehicle due to software problems or hardware issues. You can fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In certain instances the software may require reinstallation in your body control modules.

Interference

Interference can also cause the key fob not to receive or transmit an signal. This could happen when the keyfob is in close proximity to a radio transmitter like a cellphone or radar detector. Other reasons why the key fob may not function include a poor connection to the buttons or the internal chip or water damage.

If your key fob suddenly stopped working, or you have tried everything at home to resolve it (e.g. It could be a defective 500 receiver module after you've tried replacing the battery, reprogramming, and using an alternative key fob. The receiver module is located under the dash and is able to pick up the radio frequency signals from the key fob. Then, it converts them into electronic commands that the vehicle interprets.

There's a quick and easy way to reset the 500's in-board system, including the keyfob. Disconnect the battery for 15 minutes by taking off first the negative cable and then the positive cable. Reconnect the battery. This will clear out any residual electricity and restart the car's computers, which can help get your key fob working again. If the issue continues it is recommended that you consult an experienced technician. They'll be able determine the root of your issue.