• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace a Kia Sportage Replacement Key

For a variety of kia sportage car key replacement models the key comes with a keyless entry system built-in. This key usually resembles a remote control and can be exchanged with a brand new one from an 2013 kia optima key replacement dealer or a locksmith.

Key fobs are prone to malfunction due to a variety of reasons, including batteries that are dead worn buttons or buttons, water damage, signal interference and a malfunctioning receiver module. Here are some guidelines on how you can get your Kia Sportage replacement key to function again.

How to replace the remote key or smart key?

It doesn't matter if your Kia is equipped with an intelligent key, remote key, push to start key, or a regular non-transponder metal key, the battery in these keys will eventually need replacing. This is especially the case if your car displays a message telling you that the remote or smart keys have low battery power.

Luckily, this is an easy procedure. In order to replace the key fob battery take the mechanical key from the slit in the back of the key fob and pry open the cover. A small screw will be in the key fob that holds the battery in the correct position. Utilizing a small screwdriver loosen the screw and pull out the battery that was in place. Install the new battery and close the slit on the key fob.

Once the key fob has an updated battery check it by pressing the locks and unlock buttons. If the doors lock and unlock in the same way, you're set! You can now use the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or when you need to go on errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) might require their programming completed. This requires a machine for programming that is available only to the automotive locksmith or dealer. Other keys (non-transponder metal keys) do not require programming. If your key requires to be reprogrammed, you must be aware of the number that is stamped on the tag of the key code and then record it in a safe place.

How do I replace the battery?

If the 2013 kia rio key replacement key fob doesn't respond to pressing the lock or unlock button, it's a sign that the battery is low. A battery that is not functioning properly can cause other issues, such as the check engine light appearing or the engine not running properly. Fortunately, replacing the battery on the key fob is a fairly simple DIY project that requires only some basic tools.

Make sure that you shut off your vehicle and close all doors prior to starting. Locate the small metal or plastic piece that is on the bottom of your key fob, and move it until a metal key pops out. You can then insert the key into the door handle of the driver to unlock your car.

To replace the key fob battery, remove the cover on the rear and use a plastic bar tool to loosen the latch holding the black negative battery cable. Remove the old battery, and then align the replacement battery so that its "+" side is facing you, and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place and avoid excessive force to avoid damaging or bending the contacts of the metal.

After the new battery has been installed after which you turn the key fob off and on in the ignition repeatedly until the door locks cycle. You can then test your Kia's keys fob to ensure it's functioning properly.

How can you replace the smart key

Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The difference between these is that the smart key has tiny mechanical key blade in it, whereas the standard fob does not. Both key fobs have a battery that will eventually require replacement. This is a straightforward process that takes just two minutes.

Make sure to shut off your Kia, and be on a level well-lit and well-lit area before you begin. Also, remember that there are tiny pieces inside the fob which could fall out if you are not careful.

The first step is to find the small release button on the backside of the fob. It can be an oval silver button or a rectangular slot. After pressing this button, the mechanical key blade will come out and you will be able to open the key fob.

Once the key fob is removed, you can remove the battery. The new battery is a CR-2032, and can be bought through the internet or at a local auto parts store. Once you're done you should be able to lock, unlock and start your vehicle with your key fob even if your engine isn't running!

How do I replace a mechanical key

The Kia keyfob is a wonderful convenience that allows us to lock or unlock our car by simply pressing a button. But like any device it may have issues occasionally. There are ways to resolve these issues and keep your key fobs running for a long time.

One of the most frequent problems is a weak or dead battery. This can cause the device to cease working or even to stop working intermittently. If this is what you are experiencing, replace the battery with a new one.

If this does not solve the problem, use a flathead screwdriver standard to push the plastic casing of the fob open. Be sure not to damage any internal components or scratch the plastic. After opening, carefully remove the battery you have been using and replace it with a new one.

After the new battery has been put in, shut and open the doors with the mechanical key (every key fob in the kia has an emergency mechanical key that will fit in the slot). Test the key fob to verify that it's functioning properly. If the fob not working, contact a dealer or locksmith to help resolve the problem. To avoid a lockout in the future make sure you get an emergency key that will work on all door and trunk cylinders.